Investigation of Output Voltages Depending On Load In Multi Output Flyback Converter

Switched mode power supplies (SMPS) is currently preferred due to safety and high efficiency. Flyback converter, which is one of topologies used by various switches, is capable of providing voltage isolation and multioutput. This article firstly attempts to investigate the topology of multioutput flyback converter, and then to model it in a computer based simulation utilizing from mathematical analysis. This simulation based modelling is designed to control the integrated circuit (IC) by getting ratio a voltage from unloaded feedback winding. Gate pulse providing from control circuit regulate output voltages by triggering MOSFET. The feedback signal is taken from one of the windings to perform good efficiency and best cost. Although the feedback winding is at desired voltage, other output is to change according to load conditions in outputs or to input voltages, because of mutual inductance and other condition. To represent the variables in the design of a flyback power supply with six isolated output, the model have been run properly on ORCAD 16.6 by showing the transient and steady state simulations of converter. Unlike other simulation programs, this model is fully designed for all nonlinear components without using blocks.

Anahtar Kelimeler:

Multioutput flyback converter, psipice

Investigation of Output Voltages Depending On Load In Multi Output Flyback Converter

Keywords:

Multioutput flyback converter, psipice,

PDF

___

[1] Chen, T.H., Lin, W.L., Liaw, C.M., “Dynamic modeling and controller design of flyback converter”, IEEE Transactions on Aerospace and Electronic Systems 35(4): 1230 – 1239, (1999).
[2] Pressman A.I., “Switching Power Supply Design”, Second Edition, McGraw-Hill, United States of America, (1998).
[3] Wang, H., Gong, C., Ma, H., Yan, Y., “Research on a novel interleaved flyback DC/DC converter”, 1st IEEE Conference on Industrial Electronics and Applications, Singapore, 1-5 (2006).
[4] Lo, Y.K., Lin, J.Y., “Active clamping zvs flyback converter employing two transformers”, IEEE Transactions on Power Electronics, 22(6): 2416-2423, (2007).
[5] Lin, B.R., Huang, C.E., Huang, K., Wang, D., “Design and implementation of zero-voltage-switching flyback converter with synchronous rectifier”, IEE Proc.-Electr.Power Appl., 153(3): 420-428, (2006).
[6] Naresh K M ,Umavathi M , Mohan HR, “ Multi output Fly back Converter with Switching/Linear Post Regulators”, International Journal of Recent Development in Engineering and Technology, 2(6): 21-26 (2014).
[7] Tue T. Vu, Seamus O'Driscoll, John V. Ringwood, “Primary-side sensing for a flyback converter in both continuous and discontinuous conduction mode”, IET Irish Signals and Systems Conference, 1-12, Maynooth, (2012).
[8] Tiger Zhou, (2009), “Primary-Side Sensing Takes Complexity out of Isolated Flyback Converter Design”, pp.30-31, Linear Technology Magazine, 17(4): 30-31, (2009).
[9] Fairchild, “Design guidelines for off-line flyback converters using fairchild power switch”, Application Note, AN-4137, 1-18, (2003). [10] Freescale, “Semiconductor, MC34670 usage and configuration”, Application Note (AN3279), 15-30 (2009).
[11] ON Semiconductor, “How to keep a flyback switch mode supply stable with a critical-mode”, Controller Note (AN1681), 1-4, (2000).
[12] Richtek Technology, “Feedback control design of off-line flyback converter”, USA, Application Note (AN017), 3-11, (2014).
[13] Mitchell, D., Mammano, B., “Designing Stable control Loops”, Texas Instruments, Dallas, 1-3, (2002).
[14] Aström, K.J., “Control System Design Lecture Notes for ME 155A”, California, 252-253, (2002).
[15] Dixon, L.H., “Control Loop Cookbook”, Texas Instruments, Dallas, 2-8, (2002).
[16] Richtek Technology, “ACOT Stability testing”, USA: Note AN03, 2-6, (2013).