Flow and Heat Transfer Characteristics of Inclined Jet Impingement on a Flat Plate

The effects of a turbulent inclined jet impinging on a horizontal flat surface were investigated numerically with respect to the flow field and heat transfer characteristics. Main purpose of the study was to show the effects of inclined jet impingement on flow characteristics, which affects the heat transfer on a surface with a constant heat flux. Simulations were performed for different dimensionless jet-to-plate distances (2 < H/D < 8), inclination angle of the jet (45° < α < 90°), and Reynolds number (1500 < Re < 30000). The heat transfer and fluid flow characteristics have been discussed using temperature contours and velocity vectors. Initial simulation results have been validated with experimental data from the literature, and a fairly good agreement has been achieved. Results showed that by decreasing the inclination angle, a decrease in the maximum heat transfer occurs. The ratio of the maximum Nusselt number to the stagnation Nusselt number increases as the jet angle is increased. 

Flow And Heat Transfer Characteristics Of Inclined Jet Impingement On A Flat Plate

The effects of a turbulent inclined jet impinging on a horizontal flat surface were investigated numerically with respect to the flow field and heat transfer characteristics. Main purpose of the study was to show the effects of inclined jet impingement on flow characteristics, which affects the heat transfer on a surface with a constant heat flux. Simulations were performed for different dimensionless jet-to-plate distances (2 < H/D < 8), inclination angle of the jet (45° < α < 90°), and Reynolds number (1500 < Re < 30000). The heat transfer and fluid flow characteristics have been discussed using temperature contours and velocity vectors. Initial simulation results have been validated with experimental data from the literature, and a fairly good agreement has been achieved. Results showed that by decreasing the inclination angle, a decrease in the maximum heat transfer occurs. The ratio of the maximum Nusselt number to the stagnation Nusselt number increases as the jet angle is increased. 

___

  • [1] O’Donovan, T. S., Murray, D. B., Torrance, A. A., “Jet heat transfer in the vicinity of a rotating grinding wheel”, Proc. ImechE Part C: J. Mechanical Engineering Science, 220: 1-11, (2006)
  • [2] Martin, H., “Heat and Mass Transfer between Impinging Gas Jets and Solid Surfaces”, Advances in Heat Transfer, 13: 1-60, (1977).
  • [3] Viskanta, R., “Heat transfer to impinging isothermal gas and flame jets”, Experimental Thermal and Fluid Science, 6(2): 111-134, (1993)
  • [4] Polat, S., Huang, B., Mujumdar, A. S., Douglas, W. J. M., “Numerical Flow and Heat Transfer under Impinging Jets: A Review”, Annual Review of Heat Transfer, 2: 157-197, (1989)
  • [5] Lytle, D., Webb, B. W., “Air jet impingement heat transfer at low nozzle-plate spacings”, International Journal of Heat and Mass Transfer, 37(12): 1687-1697, (1994)
  • [6] Choo, K. S., Kim, S. J., “Heat transfer charachteristics of impinging air jets under a fixed pumping power condition”, International Journal of Heat and Mass Transfer, 53(1-3): 320-326, (2010)
  • [7] O’Donovan, T. S., Murray, D. B., “Fluctuating fluid flow and heat transfer of an obliquely impinging air jet”, International Journal of Heat and Mass Transfer, 51(25-26): 6169-6179, (2008)
  • [8] Kilic, M., Calisir, T., Baskaya, S., “Experimental and numerical study of heat transfer from a heated flat plate in a rectangular channel with an impinging air jet”, Journal of the Brazilian Society of Mechanical Sciences and Engineering, 39(1): 329-344, (2017)
  • [9] Kilic, M., Calisir, T., Baskaya, S., “Experimental and numerical investigation of vortex promoter effects on heat transfer from heated electronic components in a rectangular channel with an impinging jet”, Heat Transfer Research, 48(5): 435-463, (2017)
  • [10] Schueren, S., Hoefler, F., von Wolfersdorf, J., Naik, S., “Heat Transfer in an Oblique Jet Impingement Configuration With Varying Jet Geometries”, Journal of Turbomachinery, 135(2): 021010, (2012)
  • [11] Dogruoz, M.B., “Experimental and Numerical Investigation of Turbulent Heat Transfer due to Rectangular Impinging Jets”, Phd. Thesis, University of Arizona, (2005)
  • [12] Beitelmal, A. H., Saad, M. A., Patel, C. D., “The effect of inclination on the heat transfer between a flat surface and an impinging two-dimensional air jet”, International Journal of Heat and Fluid Flow, 21(2): 156-163, (2000)
  • [13] Yan, X., Saniei, N., “Heat transfer from an obliquely impining circular, air jet to a flat plate”, International Journal of Heat and Fluid Flow, 18(6): 591-599, (1977)
  • [14] Akansu, Y. E., Sarioglu, M., Kuvvet, K., Yavuz, T., “Flow field and heat transfer characteristics in an oblique slot jet impinging on a flat plate”, International Communications in Heat and Mass Transfer, 35(7): 873-880, (2008)
  • [15] Abdel-Fattah, A., “Numerical and experimental study of turbulent impinging twin-jet flow”, Experimental Thermal and Fluid Science, 31(8): 1061-1072, (2007)
  • [16] Al-Hadhrami, L. M., ”Study of Heat Transfer Distribution in a Channel with Inclined Target Surface Cooled by a Single Array of Staggered Impinging Jets”, Heat Transfer Engineering, 31(3): 234-242, (2010)
  • [17] Al-Mubarak, A. A., Shaahid, S. M., Al-Hadhrami, L. M., “Impact of Jet Reynolds Number and Feed Channel Geometry on Heat Transfer in a Channel with Inclined Target Surface Cooled by Single Array of Centered Impinging Jets with Outflow in Both Directions”, Proceedings of the World Congress on Engineering 3, London, U.K., (2011)
  • [18] Muthukannan, M., Kannan, P. R., Bajpai, A., Jeyakumar, S., “Numerical Investigation on the Fluid Flow Characteristics of a Laminar Slot Jet on Solid Block Mounted on a Horizontal Surface”, Arabian Journal for Science and Engineering, 39(11): 8077-8098, (2014)
  • [19] Goldstein, R. J., Behbahani. A. I., Heppelmann, K. K., “Streamwise distribution of the recovery factor and the local heat transfer coefficient to an impinging circular air jet”, International Journal of Heat and Mass Transfer, 29(8): 1227-1235, (1986)
  • [20] Lamont, P. J., Hunt, B. L., “The impingement of underexpanded, axisymmetric jets on perpendicular and inclined flat plates”, Journal of Fluid Mechanics, 100(3): 471-511, (1980)
  • [21] Rubel, A., “Computations of the Oblique Impingement of Round Jets upon a Plane Wall”, AIAA Journal, 19(7): 863-871, (1981)
  • [22] Sparrow, E. M., Lovell, B. J., “Heat Transfer Charachtiristics of an Obliquely Impinging Circular Jet”, Journal of Heat Transfer, 102(2): 202-209, (1980)
  • [23] Ward, J., Oladiran, M. T., Hammond, G. P., “Effect of nozzle inclination on jet impingement heat transfer in a confined cross flow”, ASME 91-HTD, 181: 25-31, (1991)
  • [24] Isman, M. K., Pulat, E., Etemoglu, A. B., Can, M., “Numerical Investigation of Turbulent Impinging Jet Cooling of a Constant Heat Flux Surface”, Numerical Heat Transfer, Part A: Applications, 53(10): 1109-1132, (2008)
  • [25] Wang, T., Lin, M., Bunker, R. S., “Flow and heat transfer of confined impingement jets cooling using a 3-D transient liquid crystal scheme”, International Journal of Heat and Mass Transfer, 48(23-24): 4887-4903, (2005)
  • [26] Attalla, M., Salem, M., “Heat transfer from a flat surface to an inclined impinging jet”, Heat and Mass Transfer, 50(7): 915-922, (2014)
  • [27] Goldstein, R. J., Franchett, M. E., “Heat Transfer From a Flat Surface to an Oblique Impinging Jet”, Journal of Heat Transfer, 110(1): 84-90, (1988)
  • [28] Baughn, J. W., Shimizu, S., “Heat Transfer Measurements From a Surface With Uniform Heat Flux and an Impinging Jet”, Journal of Heat Transfer, 111: 1096-1098, (1989)
  • [29] Rubel, A., “Oblique impingement of a round jet on a plane surface”, AIAA Journal, 20: 1756-1758, (1982).
  • [30] Geers, L. F. G., “Multiple impinging jet arrays: an experimental study on flow and heat transfer”, Phd. Thesis, Technical University Delft, (2004).
Politeknik Dergisi-Cover
  • ISSN: 1302-0900
  • Yayın Aralığı: Yılda 4 Sayı
  • Başlangıç: 1998
  • Yayıncı: GAZİ ÜNİVERSİTESİ
Sayıdaki Diğer Makaleler

MOCVD ile Büyütülen Al0.3Ga0.7N/GaN HEMT'nin Yapısal, Optik ve Elektriksel Özelliklerinin Araştırılması

A. Kürşat BİLGİLİ, Ömer AKPINAR, M. Kemal ÖZTÜRK, Süleyman ÖZÇELİK, Ekmel ÖZBAY

100Cr6 Çeliğinde Kısmi ve Tam Östenitlemede Karbür Çözünmesi Kinetiği

Ersoy ERİŞİR, Ahmet Efe GEZMİŞOĞLU

Utilization of CFD for the Aerodynamic Analysis of a Subsonic Rocket

Fatma Zeynep AYTAÇ YILMAZ, FATİH AKTAŞ

Investigation of Structural, Optical and Electrical Properties of Al0.3Ga0.7N/GaN HEMT Grown by MOCVD

Ömer AKPINAR, A.Kürşat BİLGİLİ, M. Kemal ÖZTÜRK, Süleyman ÖZÇELİK, Ekmel ÖZBAY

GaSe Kristali İçerisindeki Katkılandırma Atomlarının Doğrusal Olmayan Soğurma, Ultrahızlı Dinamikler ve İkinci Harmonik Üretimi Davranışlarına Etkisi

Ahmet KARATAY

Enerji Verimliliğinde Reaktif Güç Kompanzasyonunun Yasal Düzenlemesi

Ercan Nurcan YILMAZ, Sibel AKKAYA OY, Olcay AYDIN

Confirmation of Johnson-Cook Model Parameters for Nimonic 80A alloy by Finite Element Method

MEHMET ERDİ KORKMAZ, Mustafa GÜNAY

Büyük Veri Araçları için Eş-Derinlikli Histogram Oluşturma Metodolojisi

Ahmet Ercan TOPCU, Tolga BUYUKTANIR

Modern değişken hızlı rüzgar türbini için mikro şebekede frekans kontrolü sağlayabilecek atalet ve frekans eğim tepkisi kontrolörü

Ferhat BİNGÖL, Ali HASSAN, Müfit ALTIN

Yoğurtun İnkübasyonu ve Soğutulması için Yüksek Enerji Verimli Sistem Tasarımı

Rukiye MAVUŞ, Gülşah KARACA, Ekin Can DOLGUN, Mustafa AKTAŞ