The Investigation of Brake Linings Reinforced With Carbon Fiber

The prohibition of the asbestos in the manufacture of vehicle brake linings due to its effects on human health and the environment has led to the production and development of Non-Asbestos Organic (NAO) brake lining. The variety of materials used in Non-asbestos brake linings provided a positive effect in creating new lining compositions. In this study, the effect of car disc linings reinforced with carbon fiber on the friction performance has been examined. The mass ratio was used to determine the rate of materials contents. Test results obtained with using the Friction Assessment and Screening Test (FAST) machine showed that carbon fibers and carbon powder reinforced linings were suitable for use in vehicles.

___

Malak A, Investigate of Long-Dimension-Carbon Fiber Usage In Brake Linings, M Sc Thesis, Afyon Kocatepe University, (2014).

Belhocine A. and Bouchetara M., Thermomechanical Behaviour of Dry Contacts in Disc Brake Rotor with a Grey Cast Iron Composition, Trans Indian Inst Met, 65(3) (2012), p 231-238.

Belhocine A., Bakar A. R. A. and Abdullah, O. I., Structural and Contact Analysis of Disc Brake Assembly During Single Stop Braking Event, Trans Indian Inst Met., 68(3) (2015), p 403-410.

Reinsch E W, Sintered Metal Brake Linings For Automotive Applications, Delco - Moraine division, General Motors corp. Dayton, 2 (1970), p 9-21.

Gemalmayan N., Sürtünme Malzemelerinin Özelliklerinin Deneysel İncelenmesi, Ph D Thesis, Gazi University,Turkey (1984)

Sellami A, Kchaou M, Elleuch R, Cristol A L and Desplanques Y, Study of the interaction between microstructure, mechanical and tribo-performance of a commercial brake lining material, Materials and Design, 59 (2014), p 84 - 93.

Straffelini G, and Maines L, The relationship between wear of semimetalic friction materials and pearlitic cast iron in dry sliding, Wear, 307 (2013), p 75 - 80.

Poulios K, Svendsen G, Hiller J and Klit P, CoefŞcient of Friction Measurements for Thermoplastics and Fibre Composites Under Low Sliding Velocity and High Pressure, Tribol Lett, 51 (2013), p 191-198.

Kchaou M, Sellami A, Elleuch R, and Singh H, Friction characteristics of a brake friction material under different Friction characteristics of a brake friction material under different, Materials and Design, 52 (2013), p 533-540.

Xiao G, and Zhu Z, Friction materials development by using DOE/RSM and artificial neural metwork, Tribology International, 43 (2010), p 218 - 227.

Matejka, V., Lu, Y., Jiao, L., Huang, L., Martynkova, G. S., and Tomasek, V. Effects of silicon carbide particle sizes on friction-wear properties of friction composites designed for car brake lining aplications. Tribology International, 43 (2010), p 144 - 151.

Kukutschová J, Roubícek V, Maslán M, Jancík D, Slovák V, Malachová K, and Filip P. Wear performance and wear debris of semimetallic automotive brake materials. Wear, 268 (2010), p 86 - 93.

Ertan R. and Yavuz N., An experimental study on the effects of manufacturing parameters on the tribological properties of brake lining materials, Wear, 268 (2010), p 1524-1532.

Keskin, Ahmet. "Investigation of using natural zeolite in brake pad." Scientific Research and Essays 6.23 (2011): 4893-4904.

Sugozu, I., I. Mutlu, and A. Keskin. "Effect of ulexite and cashew on the wear and friction characteristics of automotive brake pad." Journal of The Balkan Tribological Association 22.1 A (2016): 566-578.

Mutlu, İbrahim, İlker Sugözü, and Ahmet Keskin. "The effects of porosity in friction performance of brake pad using waste tire dust." Polímeros 25.5 (2015): 440-446.

Sugözü, İlker, İbrahim Mutlu, and Ahmet Keskin. "The effect of using heat treated ulexite and cashew in automotive friction materials." Materials Testing 57.9 (2015): 744-749.

Sugözü, I.,Mutlu, I. and Keskin, A., "Friction and wear behaviour of ulexite and cashew inautomotive brake pads", Materials andTechnology, 49(5): 751-758, (2015)

Abadi S. B. K., Khavandi A. and Kharazi, Y., Effects of Mixing the Steel and Carbon Fibers on the Friction and Wear Properties of a PMC Friction Material, Appl Compos Mater, 17 (2010), p. 151-158.

Şahin S, Özdemir İ and Ünlü B S, T/M Yöntemi ile Üretilmiş Al-Si Kompoiztlerde Üretim Parametrelerinin Aşınma Davranışına Etkisi, 3rd International Powder Metallurgy Conference, Ankara, (2002), p 951-957

Yetgin S H, Aydın M and Aksoy A, The Effect of the Mixer Type and Ratio of Reinforcement Particle on the Mechanical Properties of Nbc Reinforced Al Composite Material Produced Via Powder Metallurgy, EURO PM2005 Congress And Exhibition, Prague, (2005), p 721-725.

Kuhn H A and Lawley A, Powder Metallurgy Processing New Techniques and Analyses. Academic Press, New York, (1978).

Washabaugh F J, EMOCR 66 Ultra-Short Fibers for Asbestos-Free Friction Materials. SAE(8606630), (1986).

Youssef H, and Comte C, Consolidation of High Performance Friction Materials, Elsevier Sicience Publishers, (1989).

Jain V, Saravanan M, Anandani R, Sikand R and Gupta A K, Effect of sizing on friction and wear properties of copper-iron based sintered composites, Transactions of The Indian Institute of Metals, 63(1) (2010), p 43-54.

Mutlu İ, Investigation of tribological properties of brake pads by using rice straw and rice husk dust, Journal of Applied sciences, 9(2) (2009), p 377-381.

Uygur M E, Balata Üretim Teknolojisi, 1. Ulusal Toz Metalurjisi Kongresi. Ankara, (1996).
Makine Teknolojileri Elektronik Dergisi (elektronik)-Cover
  • ISSN: 1304-4141
  • Yayın Aralığı: Yılda 5 Sayı
  • Başlangıç: 2004
  • Yayıncı: -