ÖSTEMPERLENMİŞ KÜRESEL GRAFİTLİ DÖKME DEMİRİN ABRASİV AŞINMA DAVRANIŞINA ÖSTEMPERLEME İŞLEMİNDE SOĞUTMANIN ETKİSİ
Bu çalışmada, geleneksel tek kademeli östemperleme işleminde, küresel grafitli dökme demir (KGDD) numuneler 900oC’de 1 saat östenitlenmiş, müteakiben tuz banyosunda 400oC’de 2 saat östemperlenmiştir. İkikademeli östemperleme prosesinde ise KGDD numuneler 900oC de 1 saat östenitlendikten sonra derhal 400oC’lik tuz banyosuna aktarılmış, 10 dakika bu sıcaklıkta bekletildikten sonra banyonun sıcaklığı 1.88oC/dak hızla 250oC’a soğutulmuştur. Geleneksel tek kademeli östemperleme prosesi ile üretilen üst ösferritik ve ikikademeli prosesle üretilen üst ve alt ösferritik Östemperlenmiş Küresel Grafitli Dökme Demir (ÖKGDD) numunelerin abrasiv aşınma deneyleri, disk üzerinde pim cihazında 10, 20 ve 30 N normal yük altında, 180 mesh (80 μm) boyuta sahip Al2O3 zımpara üzerinde gerçekleştirilmiştir. İki kademeli östemperleme prosesiyle üretilen küresel grafitli dökme demirin sertliği, tek kademeli prosesle üretilen dökme demirinkinden daha yüksek olmasına rağmen, her iki dökme demirin benzer abrasiv aşınma davranışı sergilediği görülmüştür. Ayrıca iki kademeli östemperlenmiş küresel grafitli dökme demirde abrasiv aşınma direnci uygulanan yükün artmasıyla artmıştır.
Anahtar Kelimeler:
Abrasive aşınma, östemperlenmiş küresel grafitli dökme demir, sertlik, mikroyapı.
EFFECT OF THE COOLING IN THE AUSTEMPERING PROCESS ON THE ABRASIVE WEAR BEHAVIOR OF AUSTEMPERED DUCTILE IRON
In this study, ductile iron was austenised at 900 o C for 1 h and austempered at 400 0 C for 2 h in single step austempering process, whereas it was austenised at 900 o C for 1 h and immediately quenched in a salt bath at 400 o C for 10 minutes and then the temperature of bath was decreased by 1.88 o C per minutes down to 250 o C in two-step austempering process. The upper ausferritic austempered ductile iron (ADI) specimens produced by conventional single step austempering process and the upper and lower ausferritic specimens produced by twostep austempering process were abraded on the pin on disc apparatus under the normal load of 10, 20, 30 N, by rubbing the specimens on abrasive Al2O3 grains with diameters of 180 Mesh (80 µm). Although the ductile iron austempered in two steps had higher hardness than the ductile iron austempered in single step, they showed similar abrasive wear behavior. In addition, the abrasive wear resistance of two step austempered specimen increased with increasing applied load.
Keywords:
Abrasive wear, austempered ductile iron, hardness, microstructure,
___
- Janowak, J.F., Gundlach, R.B., “Development of
- a Ductile Iron for Commercial Austempering”,
- AFS Transactions, 83-54,377-388, 1983.
- Harding, R.A., Gilbert, G.N.J., “Why the
- Properties of Austempered Ductile Irons Should
- Interest Engineers”, The British Foundryman,
- , 489-496, 1986.
- Walton, C.F., “Mechanical Properties of Ductile
- Iron”, Iron Castings Handbook, Iron Castings
- Society Inc., 323-376, 1981.
- Schmidt, I., Schuchert, A.Z., “Unlubricated
- Sliding Wear of Austempered Ductile Iron”,
- Metallkunde, 78, 871–875, 1987.
- Johansson, M., “Austenitic-Bainitic Ductile
- Iron”, AFS Transactions, 77-73, 117-122, 1977.
- Lerner, Y.S., “Wear Resistance of Austempered
- Ductile Iron”, Foundry Management & Technology,
- -80, 1999.
- Bartosiewicz, L., Krause, A.R., Kovacs, B.,
- Putatunda, S.K., “Fatigue Crack Growth
- Behavior of Austempered Ductile Cast Iron”,
- AFS Transactions 92 (135), 135–143, 1992.
- Bahmani, M., Elliott, R., Varahram, N., “The
- Relationship between Fatigue Strength and
- Microstructure in an Austempered Cu–Ni–Mn–
- Mo alloyed ductile iron”, Journal of Materials
- Science, 32, 5383-5388, 1997.
- Greno, G.L. Otegui, J.L., Boeri, R.E., Mechanisms
- of Fatigue Crack Growth in Austempered Ductile
- Iron”, International Journal of Fatigue, 21, 35-
- , 1999.
- Dommarco, R.C., Salvande, J.D., “Contact Fatigue
- Resistance of Austempered and Partially Chilled
- Ductile Irons”, Wear, 254, 230–236, 2003.
- Putatunda, S.K., Gadicherla, K., “Influence of
- Austenitizing Temperature on Fracture Toughness
- of a Low Manganese Austempered Ductile Iron
- (ADI) with Ferritic as Cast Structure”, Materials
- Science and Engineering A 268, 15–31, 1999.
- Rao,P., Putatunda, S.K., “Investigations on the
- Fracture Toughness of Austempered Ductile Irons
- Austenitized at Different Temperatures”, Materials
- Science and Engineering A 349, 136-149, 2003.
- Rao, P., Putatunda, S.K., “Investigations on the
- Fracture Toughness of Austempered Ductile Iron
- Alloyed with Chromium”, Materials Science
- and Engineering A 346, 254-265, 2003.
- Jianghuai Yang, J., Putatunda, S.K., “Improvement
- in Strength and Toughness of Austempered
- Ductile Cast Iron by a Novel Two-Step
- Austempering Process”, Materials and Design
- , 219–230, 2004.
- Putatunda, S.K., “Development of Austempered
- Ductile Cast Iron (ADI) with Simultaneous High
- Yield Strength and Fracture Toughness by a Novel
- Two-Step Austempering Process”, Materials
- Science and Engineering A 315, 70-80, 2001.
- Şenel, L., Çetin, M., Gül, F., “Evaluation of Dry
- Sliding Wear of Ductile Iron with Different Matrix
- Microstructures”, 3th International Advenced
- Technologies Symposium, August 18-20, Ankara,
- -166, 2003.
- Zimba, J., Simbi, D.J., Navara, E., “Austempered
- Ductile Iron: An Alternative Material for Earth
- Moving Component”, Cement & Concrete
- Composites, 25, 643-649, 2003.
- Yescas, M.A.,. Bhadeshia, H.K.D.H., “Model for
- the Maximum Fraction of Retained Austenite in
- Austempered Ductile Cast Iron”, Materials Science
- and Engineering A 333 60–66, 2002.
- Bosnjak, B., Verlinden, B., and Radulovic, B.,
- “Dry Sliding Wear of Low Alloyed Austempered
- Ductile Iron”, Materials Science and Technology,
- , 650-656, 2003.
- Hamid Ali A.S. and Elliot, R., “Influence of
- Austenitising Temperature on Austempering of
- an Mn-Mo-Cu Alloyed Ductile Iron, Part 1-
- Austempering Kinetics and the Processing
- Window”, Materials Science and Technology,
- , 1021-1031, 1996.
- Prado, J.M., Oujol, A., Cullell, J., and Tartera, J.,
- “Dry Sliding Wear of Austempered Ductile Iron”,
- Materials Science and Technology, 11, 294-298,
- -
- Owhadi, A., Hedjazi, J.,Davami, P., “Wear
- Behavior of 1.5Mn Austempered Ductile Iron”,
- Journal of Materials Science, 14, 245-250, 1998.
- Jeng, M.C., “Abrasive Wear Study of Bainitic
- Nodular Cast Iron”, Journal of Materials Science,
- , 6555-6561, 1993.
- Shepperson, S., and Allen, C., “The Abrasive Wear
- Behavior of Austempered Spheroidal Cast Irons”,
- Wear, 121, 271-287, 1988.
- Velez, J. M., Tanaka, D.K., Sinatora, A.,
- Tschiptschin, A.P., “Evaluation of Abrasive Wear
- of Ductile Cast Iron in a Single Pass Pendulum
- Device”, Wear , 251, 1315–1319, 2001.
- Çetin, M., Gül, F., “Effect of Mg on Abrasive and
- Adhesive Wear Behavior of Al-Cu Casting Alloy”,
- th International Advanced Technologies
- Symposium, August 18-20, Ankara, 134-145,
- -
- ISSN: 1300-1884
- Yayın Aralığı: Yılda 4 Sayı
- Başlangıç: 1986
- Yayıncı: Oğuzhan YILMAZ
Sayıdaki Diğer Makaleler
Bir işletmede tedarikçi değerlendirme süreci için yeni bir model tasarımı ve uygulaması
Nilay DÖNMEZ, Mustafa KURT, Metin DAĞDEVİREN
Bir tabu arama uygulaması : Esnek imalat sistemleri'nde parça seçimi ve takım magazini yerleşimi
İMALAT HÜCRESİNDE KULLANILAN BİR ROBOTUN İŞLEMLERİNİN SIRALANMASI
Farlı renkteki fluoritlerin nadir toprak elementleri ( NTE ) konsantrasyonu Kaman, Kırşehir, Türkiye
EĞİLME VE BURULMAYA MARUZ ELASTİK ROBOT KOLUNUN DİNAMİK MODELİ
Levent AKBABA, Şefaatdin YÜKSEL
Farklı sosyo-ekonomik düzeye sahip kullanıcıların konut yaşama mekanını değerlendirmesi
Farklı Renkteki Fluoritlerin Nadir Toprak Elementleri (Nte) Konsantrasyonu Kaman, Kırşehir, Türkiye
R410A SOĞUTUCU AKIŞKANININ TERMODİNAMİK ÖZELLİKLERİNİN YAPAY SİNİR AĞLARI METODUYLA MODELLENMESİ