M12 Monofilament Tipi Polipropilen Lif Takviyeli Betonların Özellikleri

Son yıllarda özellikle terörist saldırı olaylarının sık olduğu bölgelerdeki askeri yapılar için patlama ve rokete dayanıklı betonun yüksek darbe dayanımına sahip geliştirilmesine yönelik çalışmalar artmıştır. Bu amaçla kullanılan en önemli malzemelerden biri polipropilen liflerdir. Literatürde monofilament tipi PP elyaf ile yapılan çalışmalar sınırlıdır. Bu çalışmada; 32µ çapında M12 monofilament tipi PP lif, farklı oranlarda beton içerisine katılmış ve betonun rötre büzülmesi, eğilme, basınç ve çarpma mukavemeti gibi mekanik özelliklerinde meydana gelen değişimler ve mikroyapılar incelenmiştir. Lif katkısı arttıkça, rötre büzülmesinde %41 oranında azalma, basınç dayanımında düşme, eğilme mukavemetinde az miktarda da olsa iyileşme ve çarpma dayanımın da %318’ lik bir artış tespit edilmiştir. Mikroyapı incelemelerinde lif katkısının çatlayan parçaları bir arada tutarak dağılmayı engellediği görülmüştür.

Properties of Concrete Reinforced with M12 Monofilament Type Polypropylene Fiber

In recent years, especially for military structures in areas where terrorist attack incidents are frequent, studies on the development of explosion and rocket resistant concrete with high impact resistance have increased. One of the most important materials used for this purpose is polypropylene fibers. In the literature, studies with monofilament type PP fiber are limited. In this study, M12 monofilament type PP fiber with a diameter of 32 µ was added to concrete at different ratios, and changes occurring in the mechanical properties of concrete, such as shrinkage, flexural, compressive and impact strength, and microstructures were examined. It was determined that there was a 41% decrease in shrinkage, a reduction in compressive strength, a slight improvement in flexural strength, and up to 318% increase in impact strength as fiber addition increased. In the microstructural examinations, it was observed that fiber addition prevented disintegration by keeping cracked pieces together.

___

  • Oltulu M., Altun M.G., “The drop weight test method to determine impact strength of concrete and a review of research”, Gümüşhane University Journal of Science and Technology Institute, 2018, 8(1): 155-163.
  • Ünal B., Köksal F., Eyyubov C., (2003) “Polipropilen ve Çelik Liflerin Betonun Donma-Çözülme ve Aşınma Direncine Ortak Etkisi”, 5. Ulusal Beton Kongresi, Harbiye, İstanbul, Turkey, pp. 345-354.
  • Topçu İ.B., Demirel O.E., Uygunoğlu T., “Physical and mechanical properties of polypropylene fiber reinforced mortars”, Journal of Polytechnic, 2017, 20(1): 91-96.
  • Yazıcıoğlu S., Gönen T., Çobanoğlu Ö.C., (2005) “The influence of Elazıg ferrochromium slag on compressive strength and impact energy of concrete”, Sci. Eng. J. of Fırat Univ., 17(4): 681-686.
  • Şengül Ö., Doğan Ü.A., (2003) “Polimer katkılı betonların mekanik ve durabilite özellikleri”, 5. Ulusal Beton Kongresi, Harbiye, İstanbul, Turkey, pp. 163-174.
  • İpek M., Canbay M., Yılmaz K., “The effect of steel and polypropylene fibers using combination and lean on mechanical and physical properties of SIFCON”, Sakarya University Journal of Science, 2015, 19(1): 41-52.
  • Erbaş M., (2003) “Polipropilen lifler ve betonun durabilitesine etkisi”, 5. Ulusal Beton Kongresi, Harbiye, İstanbul, Turkey, pp. 593-603.
  • Kırca Ö., Şahin M., (2007) “Polipropilen Lif Kullanımının Beyaz Beton Dayanıklılığına Etkisi”, 7. Ulusal Beton Kongresi, İstanbul, Turkey, pp. 375-382.
  • Chauhan A., Chauhan P., “Natural Fibers Reinforced Advanced Materials”, J. Chem Eng Process Technol, 2013, doi:10.4172/2157-7048.S6-003.
  • Şengül Ö., Taşdemir M.A., (2007) “Doğal ve Endüstriyel Mineral Katkılar İçeren Betonların Tasarımı Mekanik Özellikleri ve Dürabilitesi”, 7. Ulusal Beton Kongresi, İstanbul, Turkey, pp. 291-300.
  • Krasnikovs A., Lapsa V. Eiduks M., “Non-traditional Reinforcement For Concrete Composites-State Of The Art”, Transport And Engineering, 2007, 24: 191-200.
  • Özşahin B., Mülayim A., Arkoç O., (2015) “The use of fiber reinforced polymers as the reinforcement of reinforced concrete Structures”, 9th International Sinan Symposium, Edirne, Turkey, pp. 109-115.
  • Yıldırım H., Sertbaş B., Berbergil V., (2007) “Kendiliğinden Yerleşen Betonlarda Polipropilen ve Çelik Lif Kullanılmasının İşlenebilirliğe Etkisi”, 7. Ulusal Beton Kongresi, İstanbul,Turkey, pp. 65-76.
  • Péra J., Ambroise J., “Fiber-reinforced Magnesia-phosphate Cement Composites for Rapid Repair”, Cement and Concrete Composites, 1998, 20: 31-39.
  • Monolis G.D., Gareis P.J., Tsonos A.D., Neal J.A., “Dynamic Properties of Polypropylene Fiber-Reinforced Concrete Slabs”, Cement and Concrete Composites, 1997, 19: 341-349.
  • Sounthararajan V.M., Jain A., Singh A.K., Thirumurugan S., Sivakumar A., “Evaluation of Composite Polypropylene Fibre Reinforced Concrete”, International Journal of Engineering and Technology, 2013, 5(2): 1817-1828.
  • Widodo S., Satyarno I., Tudjono S., “Effects of Hybrid Polypropylene-Steel Fiber Addition on Some Hardened Properties of Lightweight Concrete with Pumice Breccia Aggregate”, ISRN Civil Engineering, 2012, doi:10.5402/2012/475751.
  • Nia A.A., Hedayatian M., Nili M., Sabet V.A., “An Experimental and Numerical Study on How Steel and Polypropylene Fibers Affect The Impact Resistance in Fiber-Reinforced Concrete”, International Journal of Impact Engineering, 2012, 46: 62-73.
  • Akça K.R., Çakır Ö., İpek M., “Properties of Polypropylene Fiber Reinforced Concrete Using Recycled Aggregates”, Construction and Bulding Materials, 2015, 98: 620-630.
  • Wu Y., “Flexural Strength and Behavior of Polypropylene Fiber Reinforced Concrete Beams”, Journal of Wuhan University of Technology-Mater. Sci. Ed., 2002, 17(2): 54-57.
  • Nili M., Afroughsabet V., “The Effects of Slica Fume and Polypropylene Fibers on The Impact Resistance and Mechanical Properties of Concrete”, Construction and Bulding Materials, 2010, 24: 927-933.
  • Kakooei S., Akil H.M., Jamshidi M., Rouhi J., “The Effects of Polypropylene Fibers on The Properties of Reinforced Concrete Structures”, Construction and Bulding Materials, 2012, 27: 73-77.
  • Horbanová L., Ujhelyiová A., Ryba J., Lokaj J., Michlík P., “Properties of Composite Polypropylene Fibers for Technical Application”, Acta Chimica Slovaca, 2010, 3(2): 84-92.
  • Larbi J.A., Polder R.B., “Effects of Polypropylene Fibres in Concrete: Microstructure After Fire Testing and Chloride Migration”, HERON, 2007, 52(4): 289-306.
  • Ede A.N., Ige A.O., “Optimal Polypropylene Fiber Content for Improved Compressive and Fluxural Strength of Concrete”, IOSR Journal of Mechanical and Civil Engineering, 2014, 11(3): 129-135.
  • Saketh C., Patel J.M., Rasesh M., Sadanand G., Manoj M., “Statistical Analysis of Polypropylene Fibre Reinforced Concrete”, International Journal of Advance Research. Ideas and Innovations in Technology, 2017, 3(3): 518-532.
  • Broda J., “Application of Polyproplene Fibrillated Fibres for Reinforcement of Concrete and Cement Mortars”, High Performance Concrete Technology and Applications, Ed. Yılmaz S, Chapter 9, pp. 2016, 189-204, doi:10.5772/64386.
  • Marar K., Eren Ö., Çelik T., “Relationship between impact energy and compression toughness energy of high-strength fiber-reinforced concrete”, Materials Letters, 2001, 47: 297-304.
El-Cezeri-Cover
  • ISSN: 2148-3736
  • Yayın Aralığı: Yılda 3 Sayı
  • Başlangıç: 2013
  • Yayıncı: Tüm Bilim İnsanları ve Akademisyenler Derneği
Sayıdaki Diğer Makaleler

Yağışların Mevsimsel Değişimlerinin Eğilim Analiz Yöntemleri İle Araştırılması: Bingöl İli Örneği

Ufuk YÜKSELER, Ömerul Faruk DURSUN, Sadık ALASHAN

Sol-Jel Tekniği ile Sentezlenmiş Sr0,5Ca0,5WO4 Fosforunda Eu3+ İyonunun Lüminesans, TL Kinetik Parametreler ve Elektrokimyasal Davranışındaki Rolü

Mehmet İsmail KATI, İlker Çetin KESKİN, Murat TÜREMİŞ, Ahmet ÇETİN, Rana KİBAR

TBDY 2018 ve ASCE 41-17’e Göre Doğrusal Olmayan Hesap Yöntemleri İle Yapı Sistemlerinin Performans Analizin Elde Edilmesi ve Karşılaştırması

Rohullah JAMAL, Bahadır YÜKSEL

Düşük yoğunluklu seramik üretiminde atık kil ve pirinç kabuğu külünün geri dönüştürülmesi

İlker ÖZKAN, Esra DOKUMACI

Genleştirilmiş Cam Agregalı ve Genleştirilmiş Perlit Agregalı Şap Harçlarının Performans Özelliklerinin Belirlenmesi

Yusuf Tahir ALTUNCI, Cenk ÖCAL, Kemal SAPLIOĞLU, Hüseyin Hakan İNCE, Murat CEVİKBAS

Deprem Yüklerinin Tamamının Betonarme Perde Duvarlarla Karşılandığı Binalarda Bağ Kirişi Modellerinin Yapı Performansına Etkisi

Ömer ÖZER, Bahadır YÜKSEL

Yapay Zeka ve Makine Öğrenmesi Tekniklerinin Lojistik Sektöründe Kullanımı

Batin Latif AYLAK, Okan ORAL, Kübra YAZICI

EEG İşareti Kullanılarak Bağımlılığa Yatkınlığın Makine Öğrenmesi Teknikleri ile Analizi

Veysel YARĞI, Seda POSTALCIOĞLU

Elektrikle Çalışan Araçların Elektrik Şebekesine Olan Etkilerinin İncelenmesi

Meral KILIÇARSLAN OUACH, Ertuğrul ÇAM

Nanomateryallerin Kompozit Malzemelerin Radyasyon Zırhlama Özelliklerine Etkisinin İncelenmesi

Ali Murat SÜRÜCÜ, Serkan SUBAŞI