TIG ve MIG Kaynağı ile İşlem Gören 304 ve 1040 Çeliklerin ITAB Bölgesindeki Mekanik Özelliklerin İncelenmesi
Bu çalışmada düşük ve orta karbonlu çelik türlerinin TIG ve MIG kaynağı ile kaynak bölgesinin mekanik ve mikroyapı özelliklerine kaynak parametrelerinin etkileri incelenmiştir. Kaynak uygulaması farklı akım ve tel besleme hızlarında gerçekleştirilmiş, ardından kaynaklı birleştirmelerin mekanik özelliklerini belirlemek için çekme deneyi ve sertlik ölçümleri yapılmıştır. Ayrıca mikroyapıda meydana gelen değişiklikleri belirlemek için de mikroyapı çalışmaları yapılmıştır. Bu araştırmanın amacı öncelikle kaynak tekniklerinin malzeme kaynaklanabilirliğini nasıl etkilediği ve kaynaklı çeliklerin ısıdan etkilenen bölgede (ITAB) mekanik özelliklerini ve mikroyapı karakteristiklerindeki değişimi incelemektir. Bazı metal ve kaynaklı çeliklerin mekanik özelliklerinin tayini için testler arasında karşılaştırmalar yapılmıştır. Mikroyapılar da, kaynakların performansını dinamik koşullarda etkileyebilecek herhangi bir gözenekliliğin ve diğer özelliklerin tayinine yardımcı olmak için de kullanılmıştır.
Investigation of the Mechanical Properties of 304 and 1040 Steels in the HAZ Region by TIG and MIG Welding
In this study, the effects of welding parameters on the mechanical and microstructural properties of the weld zone and the TIG and MIG welds of low and medium carbon steels were investigated. Welding was carried out at constant welding currents and wire speeds and then tensile tests and hardness measurements were performed to determine the mechanical properties of welded joints. In addition, microstructure studies have been carried out to determine the changes in the microstructure. The aim of this research is primarily to examine how welding techniques affect material weldability and how the welded steels change in hardness, tensile test and microstructure characteristics in the heat affected zone (HAZ). Comparisons were made between the tests to determine the mechanical properties of certain metals and welded steels. Microstructures have also been used to assist in studying any porosity or other properties of the microstructure that may affect the performance of the welds under dynamic conditions.
___
- Bilici, M.K., Bakir, B., Bozkurt, Y., Çalış, Ç.,
2016. Taguchi Analysis of Dissimilar
Aluminum Sheets Joined by Friction Stir Spot
Welding, DOI: 10.5505/pajes.2015.06641.
- Çalıgülü, U., Dikbaş, H., Taşkın, M., 2012.
Microstructural Characteristic of Dissimilar
Welded Components (AISI 430 Ferritic-AISI
304 Austenitic Stainless Steels) by CO 2 Laser
Beam Welding (LBW) Gazi University Journal
of Science, 25(1), 35-51.
- Taskin, M., Ozan, S., Kolukisa, S., 2006. The
Effect of the Process Temperature on the
Bondability in Diffusion Bonding of AISI 430
with
Nodular
Cast
Iron,
Practical
Metallography, 43(6), 293-305.
- Ozan, S., Taskin, M., Kolukisa, S., 2006. The
Effect of the Process Temperature on the
Bondability in Transient Liquid Phase (TLP)
Diffusion Bonding of AISI 430 Ferritic
Stainless Steel with Nodular (Spheroid) Cast
Iron Using A Copper Interlayer, Practical
Metallography, 43(11), 575- 585.
- Tabish, T.A., Abbas, T., Farhan, M., Atiq, S.,
Butt, T.Z., 2014. Effect of Heat Input on
Microstructure and Mechanical Properties of
the TIG Welded Joints of AISI 304 Stainless
Steel International Journal of Scientific &
Engineering Research, 5(7), 1532.
- Tanaka, M., Shimizu, T., Terasaki, T., Ushio,
M., Koshiishi, F., Yang, C.L., 2006. Effects of
Activating Flux on Arc Phenomena in Gas
Tungsten Arc Welding, Science and
Technology of Welding & Joining, 5 (6),
397-402.
- Tseng, K.H., Hsu, C.Y., 2014. Performance of
Activated TIG Process in IJSER International
Journal of Scientific & Engineering Research,
5(7), 1541.
- Kurt, H.İ., Samur, R., 2013. Study on
Microstructure, Tensile Test and Hardness 304
Stainless Steel Jointed by TIG Welding,
International Journal of Science and
Technology, 2:163-168.
- Yan, J., Gao, M., Zeng, X., 2010. Study on
Microstructure and Mechanical Properties of
304 Stainless Steel Joints by TIG, Laser and Laser-TIG Hybrid Welding Optics and Lasers
in Engineering, 48, 512–517.
- Sakthivel, T., Vasudevan, M., Laha, K.,
Parameswaran, P., Chandravathi, K.S.,
Mathew, M., Bhaduri, A.K., 2011. Comparison
of Creep Rupture Behaviour of Type 316L(N)
Austenitic Stainless Steel Joints Welded by
TIG and Activated TIG Welding Processes,
Materials Science and Engineering A, 528,
6971–6980.
- Sathiya, P., Aravindan, S., Haq, A.N., 2007.
Effect of Friction Welding Parameters on
Mechanical and Metallurgical Properties of
Ferritic Stainless Steel, the International
Journal
of
Advanced
Manufacturing
Technology, 31(11-12), 1076-1082.
- Fujii, H., Sato, T., Lua, S., Nogi, K., 2008.
Development of an Advanced A-TIG
(AA-TIG) Welding Method by Control of
Marangoni Convection, Materials Science and
Engineering A, 495, 296–303.
- Topcu, I., Gulsoy, H.Ö., Kadıoglu, N.,
Gulluoglu, A.N., 2009. Processing and
Mechanical Properties of B4C Reinforced Al
Matrix Composites-Journal of Alloys and
Compounds, 482(1-2), 516-521.
- Kaya, Y., 2010. AISI 304 ve AISI 430
Paslanmaz Çeliklerin TIG, MIG ve Örtülü
Elektrod Ark Kaynağıyla Birleştirlebilirliğinin
Araştırılması, Gazi Üniversitesi Mühendislik
ve Mimarlık Fakültesi Dergisi, 25(3), 549-557.
- Gençalp İrizalp, S., Saklakoğlu, N., İldaş, G.,
Demirok, S., 2018. 1.2714 Çeliği Üzerine Sert
Dolgu Kaynağı ile Kaplanmış Fe-Cr-V Esaslı
Alaşımın Malzeme Özelliklerinin İncelenmesi.
Çukurova Üniversitesi Mühendislik-Mimarlık
Fakültesi Dergisi, 33(1), 35-46. DOI:
10.21605/cukurovaummfd.420400
- Topcu, İ., Güllüoğlu, A.N., Bilici, M.K.,
Gülsoy, H.Ö., 2018. Investigation of Wear
Behavior
ofTi-6Al-4V/CNT
Composites
Reinforced with Carbon Nanotubes, Journal of
the Facultyof Engineering and Architecture of
Gazi University (2018), https://doi.or./10.
17341/gazimmfd.460542.