Pressure Influence on the Thermophysical Properties of 316L Austenitic Stainless Steels Manufactured By Powder Metallurgy Method

Austenitic stainless steel that is used in the industrial areas such as automotive has high physical andmechanical properties. In this study; thermophysical properties of 316L austenitic stainless steel preparedby powder metallurgy method that is attracted for researchers due to obtain net or near shaped productand complex shaped materials, have been investigated. Austenitic stainless steels pressed on the 400 and600MPa pressures and pressed austenitic stainless steel samples sintered at 1200 °C temperature for anhour under inert gas atmosphere. The thermophysical features o these sintered austenitic stainless steelwere performed at temperature ranging from RT to 600 °C via heat flux type Differential ScanningCalorimeter (DSC). These properties supported by SEM images, EDS spectrums and OM (Opticmicroscope) images

Toz Metalurjisi ile Üretilen 316L Östenitik Paslanmaz Çeliklerin Termofiziksel Özelliklerin Üzerindeki Basıncın Etkisi

Otomotiv gibi endüstriyel alanlarda kullanılan östenitik paslanmaz çelik yüksek fiziksel ve mekaniksel özelliklere sahiptir. Bu çalışmada benzer ya da benzere yakın şekilli ürün ve karmaşık şekilli malzeme üretilmesine olanak sağlanmasından dolayı araştırmacılar tarafından cazip görülen toz metalurjisi yöntemiyle hazırlanan 316L östenitik paslanmaz çeliğin termofiziksel özellikleri araştırılmıştır. Östenitik paslanmaz çelikler 400 ve 600 MPa basınçlarında preslenmiş ve preslenen östenitik paslanmaz çelik numuneler 1200 °C sıcaklığında 1 sa boyunca inert gaz atmosferinde sinterlenmiştir. Bu sinterlenmiş östenitik paslanmaz çeliklerin termofiziksel özellikleri oda sıcaklığından 600 °C’ye kadar olan sıcaklık aralığında ısı akısı tipli Diferansiyel Taramalı Kalorimetreyle (DSC) ile ölçülmüştür. Bu özellikler SEM görüntüleri, EDS spektrumları ve OM (optik mikroskop) görüntüleri ile desteklenmiştir.

___

1. Morintale, E., Harabor, A., Constantinescu, C., Rotaru, P., 2015. Use of Heat Flows from DSC Curve for Calculaion of Specific Heat of the Solid Materials, Physics AUC. 23, 89-94.

2. Wielgosz, E., Kargul, T., Falkus, J., 2014. Comparison of Experimental and Numerically Calcuated Thermal Properties of Steels, International Conference on Metallurgy and Materials, Metal 2014, May 21st -23rd 2014, Brno, Czech Republic.

3. Fang, H.,, Wong, M.B., Bai, Y., 2015. Use of Kinetic Model for Thermal Properties of Steel at High Temperatures, Australian Journal of Civil Engineering, 13(1), 40-47.

4. Kelley, K.K., 1949. X. High-Temperature Heat-Content, Heat-Capacity, and Entropy Data for Inorganic Compounds, Bureau of Mines Bull. 476, 192.

5. Acar, A.N., Ekşi, A.K., Ekicibil, A., 2019. Effect of Pressure on the Magnetic and Structural Properties of X2CrNiMo17-12-2 Austenitic Stainless Steel Prepared by Powder Metallurgy Method Journal of Molecular Structure, 1198, 126876.

6. Acar, A.N., Mutlu, R.N., Ekşi, A.K., Ekicibil, A., Yazıcı, B., 2018. Effect of Temperature and Pressure on Mechanical, Surface and Electrochemical Properties of Al-1.5Cu-5.5Zn2.5Mg (Alumix-431), Anti-Corrosion Methods and Materials 65/6, 558–571.

7. Akhavan Tabatabae, B., Ashrafizadeh, F., Hassanlı, A.M., 2011. Influence of Retained Austenite on the Mechanical Properties of Low Carbon Martensitic Stainless Steel Castings, ISIJ International, 51(3), 471–475.

8. Azevedo, J.M.C., Serrenho, A.C., Allwood, J.M., 2018. Energy and Material Efficiency of Steel Powder Metallurgy, Powder Technology 328, 329–336.

9. Kulkarni, H., Dabhade, V.V., 2019. Green Machining of Powder-Metallurgy-Steels (PMS): An Overview, Journal of Manufacturing Processes 44, 1–18.

10.Butković, S., Oruč, M., Šarić, E., Mehmedović, M., 2012. Effect of Sintering Parameters on the Density, Microstructure and Mechanical Properties of the Niobium-Modified HeatResistant Stainless Steel GX40CrNiSi25-20 Produced by MIM Technology, Materiali in tehnologije/Materials and technology 46(2), 185-190.

11.Butković, S., 2013. Sinterability and Tensile Properties of Nickel Free Austenitic Stainless Steel X15CrMnMoN 17 11 3, Tehnički vjesnik (Technical Gazette) 20(2), 269-274.

12. Pandya, S., Ramakrishna, K.S., Annamalai, A.R., Upadhyaya, A., 2012. Effect of Sintering Temperature on the Mechanical and Electrochemical Properties of Austenitic Stainless Steel, Materials Science and Engineering A 556, 271–277.

13.Rudianto, H., Jang, G., Yang, S., Kim, Y., Dlouhy, I., 2015. Effect of SiC Particles on Sinterability of Al-Zn- Mg-Cu P/M Alloy”, Archives of Metallurgy and Materials, 60(2), 1383-1385.

14.Rudianto, H., Jang, G.J., Yang, S.S., Kim, Y.J. Dlouhy, I. (2015b). Evaluation of Sintering Behavior Of Premix Al-Zn- Mg-Cu Alloy Powder”, Advances in Materials Science and Engineering, Article ID 987687, 8.

15. Dyankova, S., Doneva, M., Todorov, Y., Terziyska, M., 2016. Determination of Particle Size Distribution and Analysis of a Natural Food Supplement on Pectin Base, IOSR Journal of Pharmacy, 6(5), 01-08.

16. Karthikeyan, B., Ramanathan, S., Ramakrishnan, V., 2010. A Calorimetric Study of 7075 Al/SiCp Composites, Materials and Design, 31, 92–95.

17. Karwan-Baczewska, J., 2015. Processing and Properties of Distaloy SA Sintered Alloys with Boron and Carbon, Archives of Metallurgy and Materials, 60(1), 41-45.

18. Abdoos, H., Khorsand, H., Shahani, A.R., Fatigue Behavior of Diffusion Bonded Powder Metallurgy Steel with Heterogeneous Microstructure, Materials and Design 30, 1026-1031.

19. Wilthan, B., Reschab, H., Tanzer, R., Schützenhöfer, W., Pottlacher, G., 2008. Thermophysical Properties of ChromiumNickel-Molybdenum Steel in the Solid and Liquid Phases, Int. J. Thermophys., 29, 434-444.

20.Isfahany, A.N., Saghafian, H., Borhani, G., 2011. The Effect of Heat Treatment on Mechanical Properties and Corrosion Behaviour of AISI420 Martensitic Stainless Steel, Journal of Alloys and Compounds 509, 3931–3936

21. Acar, A.N., 2019. Investigation of Physical and Mechanical Properties of 316l and 410 Stainless Steels Manufactured by Powder Metallurgy Method Doctoral Thesis, Çukurova University, Institute of Natural and Applied Sciences, 139.

22. Moteshakker, A., Danaee I., 2016. Microstructure and Corrosion Resistance of DissimilarWeld-Joints between Duplex Stainless Steel 2205 and Austenitic Stainless Steel 316L Moteshakker, A., Danaee I., Journal of Materials Science and Technology, 32, 282-290.

23. Mamat, M.F., Hamzah E., Ibrahim, Z., Rohah, A.M., Bahador, A., 2015. Effect of Filler Metals on the Microstructures and Mechanical Properties of Dissimilar Low Carbon Steel and 316L Stainless Steel Welded Joints, Materials Science Forum, 819, 57-62.

24. Simionescu, N., Benea, L., Dumitrascu, V.M., 2018. The Synergistic Effect of Proteins and Reactive Oxygen Species on Electrochemical Behaviour of 316L Stainless SteelBfor Biomedical Applications, IOP Conf. Series: Materials Science and Engineering, 374 Euroinvent ICIR 2018 17–18 May 2018, Iasi, 1-7, Romania.
Çukurova Üniversitesi Mühendislik-Mimarlik Fakültesi Dergisi-Cover
  • ISSN: 1019-1011
  • Yayın Aralığı: Yılda 4 Sayı
  • Başlangıç: 1986
  • Yayıncı: ÇUKUROVA ÜNİVERSİTESİ MÜHENDİSLİK FAKÜLTESİ
Sayıdaki Diğer Makaleler

İki Boyutlu Anizotropik Plakanın Isı İletim Analizi

Durmuş YARIMPABUÇ, Mehmet EKER, Kerimcan ÇELEBİ, Ertuğrul CİHAN

Ağ Elemanı Özelliklerinin Sayısal Model Sonuçları Üzerine Etkisinin Belirlenmesi

Oğuz ŞİMŞEK, Hüseyin İŞLEK, M. Sami AKÖZ

Ürgüp Bölgesinde Olasılık Dağılımları ile GaAs Tip PV Enerji Üretim Potansiyelinin Modellenmes

Mert İlker HAYIROĞLU

Peyniraltı Suyunun Koagülasyon/Flokülasyon Yöntemiyle Arıtılmasında Doğal Bir Koagülant Olan Montmorillonitin Kullanılması

Ayşe ÖZGÜVEN, Tuba BAYRAM, Dilara Kaya ÖZTÜRK, Erdinç ALADAĞ

Feeding Electricity Ring Grids with Minimum Interruption Using Fuzzy Logic Based Relay Coordination Scenarios Under Interruption Conditions

Mehmet Uğraş CUMA, İrfan DEMİRAY, Murat Mustafa SAVRUN

Metamalzeme Yapılarıyla Fraktal Anten Parametrelerinin İyileştirilmesi

Emin ÜNAL, Ceren DOĞAN

Madencilik Sektöründe İş Sağlığı ve Güvenliği Yönetimi için Veri Entegrasyonu Uygulaması

Mustafa ERKAYAOĞLU

Tasnif Edilmiş İnşaat Yıkıntı Atıklarından Elde Edilen Harman Tuğlası, Delikli Tuğla ve Çatı Kiremitinden Oluşan İkili Karışımların Geopolimer Hamur Üretiminde Değerlendirilmesi

Raci BAYER, İlhami DEMİR, Hüseyin ULUGÖL, Ufuk Gürkan YILDIRIM, Mustafa ŞAHMARAN

Effect of Boundary Conditions on Natural Frequencies of OrthotropicCored Composite Sandwich Beams

Sefa YILDIRIM

Ters Sarkaç Sisteminin Doğrusal Olmayan Kontrolü

Serdar COŞKUN