Eksenel Simetrik Levha Çekme İşlemlerinin Sonlu Elemanlar Yöntemi ile Analizi
Metal
levha çekme işlemlerinin sayısal yöntemlerle çözümü, sanayide zaman, işgücü ve
malzeme kaybına neden olan birden fazla kalıp üretiminin en aza indirilmesini
sağlamaktadır. Metal levha işlemlerinin analizinde kullanılan sayısal
yöntemlerin en etkin ve yaygın olanı sonlu elemanlar yöntemidir. Bu yöntemle
malzemenin şekil değişimini ve buna bağlı olarak kalınlık değişimini saptamak
mümkün olmaktadır. Böylece gerekli taslak geometrisi önceden
belirlenebilmektedir. Bu çalışmada, eksene göre simetrik parçaların çekme
işlemi sırasındaki şekil değişimi üç boyutlu bir sonlu elemanlar yöntemi ile
incelenmiştir.
___
- 1. Woo, D.M., The Analysis of Axisymmetric
Forming of Sheet Metal and the Hydrostatic
Bulging Process, Int. J. Mech. Sci., 6
(1964) 303-317.
- 2. Woo, D.M., On the Complete Solution of
the Deep Drawing Problem, Int. J. Mech.
Sci., 10 (1968) 83-94.
- 3. Chakrabarty, J., A Theory of Stretch
Forming over Hemispherical Punch Heads,
Int. J. Mech. Sci., 12 (1970) 315-325.
- 4. Wang, N.M., Large Plastic Deformation of a
Circular Sheet Caused by Punch Stretching,
Trans., ASME, Journal of Applied
Mechanics, 37 (1970) 431-440.
- 5. Kaftanoğlu, B., An Investigation of Stretch
Forming in Relation to Deep Drawing and
Testing Sheet Metal, Ph.D. Thesis, Imperial
College, London, 1966.
- 6. Kaftanoğlu, B. ve Alexander, J.M., On
Quastatic Axisymmetrical Stretch Forming,
Int. J. Mech. Sci., 12 (1970) 1065-1084.
- 7. Wifi, AS., An Incremental Complete
Solution of the Stretch Forming and Deep
Drawing of a Circular Blank using a
Hemispherical Punch, Int. J. Mech. Sci., 18
(1976) 23-31.
- 8. Wang, N.M. ve Budiansky, B., Analysis of
Sheet Metal Stamping by a Finite Element
Method, Trans., ASME, Journal of Applied
Mechanics, 45 (1978) 73-82.
- 9. Mattiasson, K., Saran, M., Melander, A.,
Schedi, E. ve Gustafsson, C., Finite
Element Simulation of Deep Drawing of
Low and High Strength Stcel, Advanced
Technology of Plasticity, Vol. 1, K. Lange
(Ed), Springer-Verlag, 1987, pp. 657-664.
- 10. Darendeliler, H., Computer-Aided
Deformation Analysis of Deep-Drawing
Process, Doktora Tezi, Makina
Mühendisliği Bölümü, Orta Doğu Teknik
Üniversitesi, Ankara, 1991.
- 11. Darendeliler, H. ve Kaftanoğlu, B.,
Deformation Analysis of Deep Drawing by
a Finite Element Method, Annals of the
CIRP, 40/1 (1991) 281-284.
- 12. Malvern, L.E., Introduction to the
Mechanics of a Continuous Medium,
Prentice-Hall, Inc., New Jersey, 1969.
- 13. Eringen, A.C., Nonlinear Theory of
Continuous Media, McGraw-Hill Book
Company, Inc., New York, 1962.
- 14. Yamada, Y., Yoshimura, N. ve Sakurai, T.,
Plastic Stress-Strain Matrix and Its
Application for the Solution of
Elastic-Plastic Problems by the Finite
Element Method, Int. J. Mech. Sci., 10
(1968) 343-354.
- 15. Ahmetoğlu, M., Kinzel, G.L. ve Altan, T.,
Deep Drawing of Round Cups Using
Variable Blank Holder Force, Report No.
ERC/NSM-S-92-50, Engineering Research
Center for Net Shape Manufacturing, The
Ohio State University, 1992.
- 16. Saran, M.J., Schedin, E., Samuelsson, A.,
Melander, A., and Gustafsson, C.,
Numerical and Experimental Investigations
of Deep Drawing of Metal Sheets, Trans.,
ASME, Journal of Engineering for Industry,
112 (1990) 272-277.