___

• Padmanabhana, R., Oliveira, M. C., Baptista, A.
• J., Alves, J. L., Menezes, L. F., “Blank Design for
• Deep Drawn Parts Using Parametric NURBS
• Surfaces”, Journal of Materials Processing
• Technology, Vol. 209, 2402–2411 pp., 2009.
• Saxena, R. K. and Dixit, P. M., "Finite Element
• Simulation of Earing Defect in Deep Drawing",
• Int. J. Adv. Manuf. Technol., DOI
• 1007/s00170-009-1963-5., 2009.
• Yang, T. S., "Finite Element Analysis of Square
• Cup Deep Drawing of Pure Titanium Metal Sheet
• at Elevated", Advanced Design and
• Manufacture to Gain a Competitive Edge,
• Springer – Verlag London Limited 33–42, 2008.
• Demirci, H. I., Esner, C., Yasar, M., "Effect of
• The Blank Holder Force on Drawing of
• Aluminum Alloy Square Cup: Theoretical and
• Experimental Investigation", Journal of
• Materials Processing Technology, Vol. 206,
• –160, 2008.
• Gavas, M. and Izciler, M., "Effect of Blank Holder
• Gap on Deep Drawing of Square Cups",
• Materials and Design, Vol. 28, 1641–1646, 2007.
• Gavas, M. and Izciler, M., "Design and
• Application of Blank Holder System with Spiral
• Spring in Deep Drawing of Square Cups",
• Journal of Materials Processing Technology,
• Vol.171, 274–282, 2006.
• Menezes, L. F. and Teodosiu, C., "Three-
• Dimensional Numerical Simulation of The Deep-
• Drawing Process Using Solid Finite Elements",
• Journal of Materials Processing Technology,
• Vol. 97, 100–106, 2000.
• Marumo, Y., Saiki, H., Mori, T., "Combined
• Effects of Strain Hardening Characteristics and
• Tool Geometry on The Deep-Drawability of
• Square Aluminum Cups", Journal of Materials
• Processing Technology, Vol. 89–90, 30–36,
• -
• Marumo, Y. and Saiki, H., "Evaluation of The
• Forming Limit of Aluminum Square Cups",
• Journal of Materials Processing Technology,
• Vol. 80–81, 427–432, 1998.
• Özek C, Bal M.," The Effect of Die/Blank Holder
• and Punch Radiuses on Limit Drawing Ratio in
• Angular Deep-Drawing Dies", J. Adv. Manuf.
• Technol., Vol. 40, 1077-1083., 2009.
• Gea, H. C. and Ramamurthy, R., "Blank Design
• Optimization on Deep Drawing of Square Shells",
• IIE Transactions, Vol. 30, 913–921, 1998.
• Mamalis, A. G., Manolakos, D. E., Baldoukas, A.
• K., "Simulation of Sheet Metal Forming Using
• Explicit Finite Element Techniques: Effect of
• Material and Forming Characteristics Part 2.
• Deep-Drawing of Square Cups", Journal of
• Materials Processing Technology, Vol. 72, 110–
• , 1997.
• Özek, C., Bal, M., "Derin Çekme Kalıplarında
• Matris-Zımba Radyüsü ve Çekme Oranının Et
• Kalınlığı Üzerindeki Etkisi", Journal of the
• Faculty of Engineering and Architecture of
• Gazi University, Cilt 24, No 1, 33-41, 2009.
• Saniee, F. F. and Montazeran, M. H., "A
• Comparative Estimation of The Forming Load in
• The Deep Drawing Process", Journal of
• Materials Processing Technology, Vol. 140,
• No:1-3, 555-561, 2003.
• Swift W, Chung S.Y., "Cup Drawing From a Flat
• Blank-Experimental Investigation", Proc. Int.
• Mech. Eng., 199–211, 1951.